Beijer-electronics iX Panel T70 EN Manual de usuario Pagina 1

iXPanelT70Service&MaintenanceManualEnglishMAEN006,2010-05

Installation3Installation3.1 SpaceRequirements• Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch)• Space requirements when installing the

Installation2.Place the panel cut out where the operator panel is to be situated, draw alongthe outer sides of the holes and cut according to the mark

Installation4.Connect the cables in the specified order, according to the drawing and stepsbelow.Caution:• Ensurethattheoperatorpanelandthecontrollersy

Installation3.2.1 ConnectionstotheControllerFor information about the cables to be used when connecting the operator panel tothe controller, please re

Technical Data4TechnicalDataParameter iX Panel T70Frontpanel,WxHxD 219x154x6mmMountingdepth 56mm(156mmincludingclearance)Frontpanelseal IP66Rear panel

Chemical Resistance5 ChemicalResistance5.1 MetalCasingThe frame and casing material is powder-coated aluminum. This powder paintwithstands exposure to

Chemical Resistance5.2 TouchScreenandOverlay5.2.1 AutotexF157/207Autotex F157 or F207 covers the overlay surrounding the touch screen.SolventR esistan

Chemical Resistance5.2.2 TouchScreenSurfaceThetouchscreensurfaceonthepanelwithstandsexposuretothefollowingsolvents without visible change:Solvents Tim

Hardware Tests6 HardwareTestsBefore the operator panels are approved for market introduction, they are testedby independent authorities. The iX Panels

Additional Hardware7 AdditionalHardware7.1 MemoryCardAn internal Compact Flash memory card can be used in iX Panel T70 forexpansion of the project mem

ForewordService&MaintenancemanualforiXPanelT70ForewordThis manual contains detailed information about iX Panel T70, includingdescriptions of vario

Additional Hardware5.Re-attach the back cover to the operator panel.6.Turn on the power to the operator panel.When the operator panel starts up, you w

Hardware Replacement8 HardwareReplacementThis section contains instructions on how to replace operator panel hardware.Only components included in the

Hardware ReplacementMODE Description1100 Notused(runmode).1110 Self-test.xxx1 Hardreset(forcesthesystemtorese t).To ch ange mode switches, follow the

Hardware Replacement8.3 ReplacingtheRearCoverThe following is needed:• Anewrearcover,seeAvailable Spare Parts for iX Panel T70• AtorxT10screwdriverNot

Hardware Replacement8.4 ReplacingtheDisplay/DisplayCableThe following is needed:• A new display including plastic frame and display cable, seeAvailabl

Hardware Replacement8.4.1 Self-testoftheDisplayTo perform a self-test of the display, follow the steps below:1.Start the operator panel in a self-test

Hardware Replacement8.5 ReplacingtheCompleteFrontThe following is needed:• Anewfront,seeAvailable Spare P arts for iX Panel T70• AtorxT10screwdriverNo

Hardware Replacement8.6 ReplacingtheBacklightIf the backlight of the iX Panel T70 is broken, the entire display must be replaced.To replace the displa

Hardware Replacement8.7 AvailableSparePartsforiXPanelT70Ordernumber Description601009274 COMPLETEFRONTIncludingfrontcover,touchoverlay,gasketsandlabel

Service Menu9ServiceMenuThe service menu for the operator panel can be accessed before a project isdownloaded, or by setting the mode switches in mode

ContentsContents1 Safety Precautions ... 51.1 General ...

Service Menu9.3.3 EraseProjectThe erase function will detect if the project is located in the panel memory or on amemory card. Pressing Erase Project

Hardware Self Test10 HardwareSelfTestThe self-test program can be used to test aspects of operator panel functionalityand the communication ports. To

Additional Installation Tips11 AdditionalInstallationTipsWhen experiencing communication problems in for example noisy environmentsor when operating c

Additional Installation Tips11.2 EthernetConnectioninthePanel123451-12-23-38-8RJ45RJ45RJ45RJ45RJ45RJ45RJ45RJ45Industrial EthernetOperator panelOperato

Additional Installation Tips11.3 ToAchieveBetterEMCProtection• Initially, use the original cabling from Beijer Electronics primarily.• Use shielded ca

Additional Installation Tips11.4 AmbientTemperatureThe maximum ambient temperature for the operator panel is provided in thespecifications. The ambient

Additional Installation Tips11.5 SafetyMost of the operator panels are fed with 24 V DC.412434Power supply230 V AC to 24 V DCPower supply230 V AC to 2

Additional Installation Tips11.6 GalvanicIsolationUSBUSBRS232RS422/485+24 V DC0 VFilterDC/DCgalvanic isolationVCC0 V (GND)DC/ACCFLEthernetInternal ele

Additional Installation Tips11.7 CableandBusTerminationRS485• Use shielded and twisted pair cable. The pair capacitance may not exceed 52.5pF/m and ar

Fault Tracing12 FaultTracingThis section includes different fault scenarios and steps to follow to trace the fault.TheiXPanelT70isnotworkingproperly,a

Contents9.3.3 EraseProject ...309.3.4 FormatMemoryCard ...30

Fault TracingTheiXPanelT70isworking,butoneormorekeysarenotworking1.Check that the flex cables are correctly fitted.2.Replace the front according to the

Software13 SoftwareThis chapter describes how to maintain and update the software in the iX Panels.The chapter includes a general description of the o

Software13.2 UpdateSoftwareWhen an update is available, an e-mail is sent to the distributors. The software isalso available on the manufacturer’s web

SoftwareTransferImage1.Double-click on the executable Image Loader file to start the transfer program.2.Follow the instructions.The image transfer proc

Environmental Aspects14 EnvironmentalAspectsThis chapter includes inform ation about the environmental impact of iX Panels.More information can be fou

Environmental Aspects14.3 RecyclingThe operator panels consist largely of aluminum. It is a great advantage in terms ofboth resources and the environm

HEADOFFICE SUBSIDIARIESSWEDEN GERMANY USABeijerElectronicsProductsAB Elektronik-SystemeLauerGmbH&Co. KG BeijerElectronicsInc.Box426 Kelterstraße59

Safety Precautions1SafetyPrecautionsBoth the installer and the owner and/or operator of the operator panel must readand understand this installation m

Safety Precautions1.3 DuringUse• Keep th e operator panel clean.• Emergency stop and other safety functions may not be controlled from theoperator pan

Introduction2IntroductionThis manual describes how to maintain the iX Panel T70.The functions available in iX Developer depend on which operator panel

Introduction2.2 MaintenanceCarefully read the instructions before beginning maintenance on the operatorpanel.• Only qualified personnel should carry ou

Introduction2.5 ContactandSupportIf you want to report a fault or have a question about the operator panels, pleasecontact your local supplier or fill